Subcategories

• Core2 for AWS
  50
  Topics
  237
  Posts

  R

  so what are you doing so far to display image on button press? example of your code?

• M5Stack Fire
  86
  Topics
  330
  Posts

  R

  お世話になります。

  現在、M5Stack FIRE に関して次の2つのバージョンがあります。
  　　1) V2.6 (USBチップ: CH9102F) ※BALA2 FIREとして購入したもの
  　　2) V2.7 (USBチップ: CH9102F)
  2)のV2.7については、Windows11(24H2)で問題なくUSBシリアルポート接続
  認識ができていますが、同一環境(PC環境、USB接続環境、USBケーブル等)
  で、1)のV2.6について、デバイスマネージャでCOMポートとして認識できず
  困っています。

  様々なUSB環境(ハブ、ケーブル等)で試していますが、一瞬接続できたことも
  過去にありましたが、現状は、ことごとく正しく認識されません。

  もし、同様のトラブルに遭遇された方で、アドバイスなどがございましたら
  よろしくお願いします。

  Ruri

• M5stack Grey
  64
  Topics
  227
  Posts

  D

  Burn of UIFlow2 (v2.2.4-16MB) to M5Core-Grey using M5Burner loads stub but not full firmware. Burn of UIFlow_M5GO (same M5Burner) works fine. The UIFlow2 burn results in inoperable M5GO even though final message says 'Burn Successfully, click here to return'.

  Here is screen shot of output from Burn:

  --chip auto --port /dev/tty.usbserial-01DB92E6 --baud 1500000 --before default_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size detect 0x9000 /Applications/M5Burner.app/Contents/Resources/packages/tmp/uiflow2-cfg.bin
  esptool.py v4.7-dev
  Serial port /dev/tty.usbserial-01DB92E6
  Connecting...
  .

  Detecting chip type... Unsupported detection protocol, switching and trying again...
  Connecting...
  .

  Detecting chip type...
  ESP32
  Chip is ESP32-D0WDQ6 (revision v1.0)
  Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
  Crystal is 40MHz
  MAC: 98:f4:ab:6c:dc:00
  Uploading stub...
  Running stub...
  Stub running...
  Changing baud rate to 1500000
  Changed.
  Configuring flash size...
  Auto-detected Flash size: 16MB
  Flash will be erased from 0x00009000 to 0x0000efff...
  Compressed 24576 bytes to 475...
  Writing at 0x00009000... (100 %)
  Wrote 24576 bytes (475 compressed) at 0x00009000 in 0.2 seconds (effective 1153.6 kbit/s)...
  Hash of data verified.

  Leaving...
  Hard resetting via RTS pin...

• M5 Stick/StickC

  M5Stack's little brother. Discuss M5 Stick hardware and software related issues here

  387
  Topics
  1.5k
  Posts

  S

  6294ebf3-7db1-4597-81ab-f50c514b84b9-image.png
  here, there is no time zone with any :30min option, so working with RTC clock is not feasible, is there any workaround for this or will this be fixed soon?

• M5GO
  17
  Topics
  70
  Posts

  C

  @teastain thank you!

• FACES Kit
  27
  Topics
  114
  Posts

  M

  Problem:

  Der Schrittmotor funktioniert nur korrekt in der Z-Achse bei normalen (langsamen) Drehgeschwindigkeiten.
  Beim Versuch, die X- und Y-Achsen zu verwenden, funktioniert der Motor nur, wenn ich die Vorschubgeschwindigkeiten auf das 10-fache oder höher erhöhe.
  Wenn ich versuche, die Adresse auf 0x71 zu ändern, wird das Modul nicht erkannt.

• M5Stick V
  47
  Topics
  127
  Posts

  S

  Hi, some suggestions for the next hw iteration:

  connect imu irq pin connect rtc irq pin to esp32 to let us know whether the irq comes from power button or rtc let the buttons go out the case for easier access reduce time of power on btn to a single click seperate LED and IR for incognito use add the L-R-Center button from the M5Paper
• Core 2

  For Topics related to the Core 2

  323
  Topics
  1.4k
  Posts

  P

  @robski it is not showing in VS Code. First I thougt that it was a problem of VS Code, that is why I tried it with MU.
  a2cae0c1-d731-4423-9758-af3088b68478-image.png