Posts made by admiralmaggie

Thanks @macsbug . In addition to resolution and refresh rate, is there anything else I can play around with?

Hello,
I have one of the new Display 13.2 Modules (M126). I've been able to get the example program working with a few different HDMI displays but I have a smaller HDMI display where I cannot get to display anything. This is a new module and I can't find any information on troubleshooting steps. Besides resolution and refresh rate, what other settings can I play around with?

static M5ModuleDisplay display(800, 480, 60);

Thank you in advance!

Here is the debug log output:

rst:0x1 (POWERON_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13104
load:0x40080400,len:3036
entry 0x400805e4
[ 7][D][esp32-hal-cpu.c:244] setCpuFrequencyMhz(): PLL: 480 / 2 = 240 Mhz, APB: 80000000 Hz
[ 455][I][esp32-hal-psram.c:96] psramInit(): PSRAM enabled
[ 489][I][M5GFX.cpp:482] init_impl(): [M5GFX] [Autodetect] load from NVS : board:3
[ 490][I][esp32-hal-i2c.c:75] i2cInit(): Initialising I2C Master: sda=21 scl=22 freq=100000
[ 495][D][M5GFX.cpp:694] autodetect(): [M5GFX] AXP192 found
[ 503][D][M5GFX.cpp:445] _read_panel_id(): [M5GFX] [Autodetect] read cmd:04 = ff0000e3
[ 508][I][M5GFX.cpp:787] autodetect(): [M5GFX] [Autodetect] M5StackCore2
[ 635][I][esp32-hal-i2c.c:75] i2cInit(): Initialising I2C Master: sda=21 scl=22 freq=100000
[ 636][V][Touch_FT5x06.cpp:63] _check_init(): [FT5x06] CIPHER:0x64 / FIRMID:0x10 / VENDID:0x11
[ 641][I][esp32-hal-i2c.c:75] i2cInit(): Initialising I2C Master: sda=21 scl=22 freq=100000
[ 686][D][M5ModuleDisplay.h:111] init_impl(): [LGFX] pkg:0
[ 687][D][M5ModuleDisplay.h:136] init_impl(): [LGFX] ModuleDisplay with Core2/Tough
[ 688][I][Panel_M5HDMI.cpp:435] init(): [M5HDMI] i2c port:1 sda:21 scl:22
[ 695][I][esp32-hal-i2c.c:75] i2cInit(): Initialising I2C Master: sda=21 scl=22 freq=100000
[ 704][I][Panel_M5HDMI.cpp:442] init(): [M5HDMI] Chip ID: 17 02 e2

[ 709][I][Panel_M5HDMI.cpp:448] init(): [M5HDMI] Resetting HDMI transmitter...
[ 718][I][Panel_M5HDMI.cpp:108] LOAD_FPGA(): [M5HDMI] Erase FPGA SRAM...
[ 731][I][Panel_M5HDMI.cpp:124] LOAD_FPGA(): [M5HDMI] Starting Writing to SRAM...
[ 1222][I][Panel_M5HDMI.cpp:168] LOAD_FPGA(): [M5HDMI] SRAM Prog Finish...
[ 1222][I][Panel_M5HDMI.cpp:460] init(): [M5HDMI] Waiting the FPGA gets idle...
[ 1225][I][Panel_M5HDMI.cpp:473] init(): [M5HDMI] FPGA ID:48 44 00 03
[ 1231][I][Panel_M5HDMI.cpp:480] init(): [M5HDMI] Initialize HDMI transmitter...
[ 1574][I][M5GFX.cpp:482] init_impl(): [M5GFX] [Autodetect] load from NVS : board:3
[ 1575][I][esp32-hal-i2c.c:75] i2cInit(): Initialising I2C Master: sda=21 scl=22 freq=100000
[ 1580][D][M5GFX.cpp:694] autodetect(): [M5GFX] AXP192 found
[ 1590][D][M5GFX.cpp:445] _read_panel_id(): [M5GFX] [Autodetect] read cmd:04 = ff0000e3
[ 1593][I][M5GFX.cpp:787] autodetect(): [M5GFX] [Autodetect] M5StackCore2
[ 1751][I][esp32-hal-i2c.c:75] i2cInit(): Initialising I2C Master: sda=21 scl=22 freq=100000
[ 1752][V][Touch_FT5x06.cpp:63] _check_init(): [FT5x06] CIPHER:0x64 / FIRMID:0x10 / VENDID:0x11