That did fix it, thank you so much. <3
I did notice that error, just still familiarizing myself with arduino and wasn't sure how to go about it.

Working code follows for anyone wondering.

#include <M5StickCPlus.h>
#include "M5_ENV.h"

SHT3X sht30;
QMP6988 qmp6988;

float tmp = 0.0;
float hum = 0.0;
float pressure = 0.0;

void setup() {
  M5.begin();
  M5.Lcd.setRotation(3);
  Wire.end();
  Wire.begin(0,26);
  qmp6988.init();
}

void loop() {
  pressure = qmp6988.calcPressure();

  sht30.get();

  tmp = sht30.cTemp;
  hum = sht30.humidity;

  M5.Lcd.fillScreen(BLACK);
  M5.Lcd.setCursor(0, 0);
  M5.Lcd.printf("Temp: %2.1f\r\nHumi: %2.0f%%\r\nPressure:%2.0fPa\r\n", tmp, hum, pressure);
  delay(1000);
}

Having an issue running the following code with the env-iii hat. Any help would be appreciated.

#include <M5StickCPlus.h>
#include "M5_ENV.h"

SHT3X sht30;
QMP6988 qmp6988;

float tmp = 0.0;
float hum = 0.0;
float pressure = 0.0;
int status;

void setup() {
  M5.begin();
  //M5.Axp.ScreenBreath(8);
  M5.Lcd.setRotation(3);
  Wire.begin(0,26);
  qmp6988.init();
}

void loop() {
  pressure = qmp6988.calcPressure();

  status = sht30.get();

  tmp = sht30.cTemp;
  hum = sht30.humidity;

  M5.Lcd.fillScreen(BLACK);
  M5.Lcd.setCursor(0, 0);
  M5.Lcd.printf("Temp: %2.1f\r\nHumi: %2.0f%%\r\nPressure:%2.0fPa\r\nStatus: %d", tmp, hum, pressure, status);
  delay(4000);
}

04:49:47.756 -> [ 2][I][esp32-hal-i2c.c:75] i2cIni��): Initialising I2C Master: sda=32 scl=33 freq=100000
04:49:47.756 -> [ 5][D][esp32-hal-cpu.c:244] setCpuFrequencyMhz(): PLL: 480 / 2 = 240 Mhz, APB: 80000000 Hz
04:49:47.796 -> M5StickCPlus initializing...[ 78][I][esp32-hal-i2c.c:75] i2cInit(): Initialising I2C Master: sda=21 scl=22 freq=100000
04:49:48.391 -> OK
04:49:48.391 -> E (645) ledc: freq_hz=0 duty_resolution=13
04:49:48.391 -> [ 649][E][esp32-hal-ledc.c:75] ledcSetup(): ledc setup failed!
04:49:48.391 -> [ 649][W][Wire.cpp:301] begin(): Bus already started in Master Mode.
04:49:48.391 -> [ 653][W][Wire.cpp:301] begin(): Bus already started in Master Mode.
04:49:49.506 -> [ 1760][E][Wire.cpp:513] requestFrom(): i2cRead returned Error 263
04:49:50.512 -> [ 2761][E][Wire.cpp:513] requestFrom(): i2cRead returned Error 263