How to flash tasmona or anything to M5Stack ATOM Lite using esptool?
-
Hi, I've tried so many things, but what is the correct way to flash a firmware to the M5Stack ATOM Lite ESP32 Development Kit using esptool? This (among many other commands) is not working
esptool.py --chip auto --port /dev/ttyUSB0 --baud 115200 --before default_reset --after hard_r^Cet write_flash -z --flash_mode dio --flash_freq 40m --flash_size detect 0x1000 /home/romeokienzler/Downloads/tasmota32.bin
When I look at the serial monitor of the arduino IDE i get
11:10:25.593 -> rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
11:10:25.593 -> configsip: 188777542, SPIWP:0xee
11:10:25.593 -> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
11:10:25.593 -> mode:DIO, clock div:2
11:10:25.593 -> load:0x3f400020,len:289900
11:10:25.958 -> ets Jun 8 2016 00:22:57 (edited) -
Hello @romeokienzler
M5Atom lite essentially is just another ESP32 based device so I'd guess the regular Tasmota instructions should work (not tested myself though). Have you tried the instructions here?
Good luck!
Felix -
@romeokienzler said in How to flash tasmona or anything to M5Stack ATOM Lite using esptool?:
after hard_r^Cet
Just to point out a possible issue, it looks I like you have a Control-C in your command by mistake. Is that a copy/paste error?
-
-
Checking out Stackoverflow now :) https://stackoverflow.com/questions/66514659/how-to-flash-tasmota-or-anything-to-m5stack-atom-lite-esp32-pico-d4-using-es
-
I have alsoo a problem with esptool
.
.
.
.
.
.
.
.
Traceback (most recent call last):
File "esptool\cmds.py", line 94, in detect_chip
File "esptool\loader.py", line 378, in check_command
File "esptool\loader.py", line 347, in command
File "esptool\loader.py", line 279, in read
File "esptool\loader.py", line 1387, in slip_reader
esptool.util.FatalError: Serial data stream stopped: Possible serial noise or corruption.During handling of the above exception, another exception occurred:
Traceback (most recent call last):
File "esptool.py", line 34, in <module>
File "esptool_init_.py", line 995, in main
File "esptool_init.py", line 637, in main
File "esptool_init_.py", line 880, in get_default_connected_device
File "esptool\cmds.py", line 121, in detect_chip
File "esptool\loader.py", line 603, in connect
File "esptool\loader.py", line 544, in _connect_attempt
File "esptool\loader.py", line 407, in sync
File "esptool\loader.py", line 323, in command
File "serial\serialutil.py", line 372, in timeout
File "serial\serialwin32.py", line 222, in _reconfigure_port
serial.serialutil.SerialException: Cannot configure port, something went wrong. Original message: PermissionError(13, 'A device attached to the system is not functioning.', None, 31)
[6352] Failed to execute script 'esptool' due to unhandled exception!before clicking the burn button on m5burner, I push the button to enter boot mode green led is flashing