Any updates on the mpu6886?

[Xeon]

Can this be used somehow?
i haven't found any examples.

[staberas]

@xeon sorry for resurrecting old post, i had the same problem, i currently close getting data from the IMU

[staberas]

done, used party code from anoken who sourced it from the arduino version , i clean up and updated it

import image
import lcd
import sensor
import sys
import time
import utime
from board import board_info
import KPU as kpu
from Maix import GPIO
from fpioa_manager import *
from pmu import axp192 
from machine import I2C
#pmu = axp192() - breaks IMU data -
#pmu.enablePMICSleepMode(True) - breaks IMU data -

i2c = I2C(I2C.I2C0, freq=400000, scl=28, sda=29)
#devices = i2c.scan()
lcd.init()

# IMU6866 define
MPU6886_ADDRESS=0x68
MPU6886_WHOAMI=0x75
MPU6886_ACCEL_INTEL_CTRL=0x69
MPU6886_SMPLRT_DIV=0x19
MPU6886_INT_PIN_CFG=0x37
MPU6886_INT_ENABLE=0x38
MPU6886_ACCEL_XOUT_H=0x3B
MPU6886_TEMP_OUT_H=0x41
MPU6886_GYRO_XOUT_H=0x43
MPU6886_USER_CTRL= 0x6A
MPU6886_PWR_MGMT_1=0x6B
MPU6886_PWR_MGMT_2=0x6C
MPU6886_CONFIG=0x1A
MPU6886_GYRO_CONFIG=0x1B
MPU6886_ACCEL_CONFIG=0x1C
MPU6886_ACCEL_CONFIG2=0x1D
MPU6886_FIFO_EN=0x23

# IMU6866 Initialize
def write_i2c(address, value):
	i2c.writeto_mem(MPU6886_ADDRESS, address, bytearray([value]))
	time.sleep_ms(10)

write_i2c(MPU6886_PWR_MGMT_1, 0x00)
write_i2c(MPU6886_PWR_MGMT_1, 0x01<<7)
write_i2c(MPU6886_PWR_MGMT_1,0x01<<0)
write_i2c(MPU6886_ACCEL_CONFIG,0x10)
write_i2c(MPU6886_GYRO_CONFIG,0x18)
write_i2c(MPU6886_CONFIG,0x01)
write_i2c(MPU6886_SMPLRT_DIV,0x05)
write_i2c(MPU6886_INT_ENABLE,0x00)
write_i2c(MPU6886_ACCEL_CONFIG2,0x00)
write_i2c(MPU6886_USER_CTRL,0x00)
write_i2c(MPU6886_FIFO_EN,0x00)
write_i2c(MPU6886_INT_PIN_CFG,0x22)
write_i2c(MPU6886_INT_ENABLE,0x01)

# Read IMU6866 and Scaling
def read_imu():
	aRes=255/4096/2
	gRes = 2000.0/32768.0
	offset=128
	accel = i2c.readfrom_mem(MPU6886_ADDRESS, MPU6886_ACCEL_XOUT_H, 6)
	accel_x = (accel[0]<<8|accel[1])
	accel_y = (accel[2]<<8|accel[3])
	accel_z = (accel[4]<<8|accel[5])
	if accel_x>32768:
		accel_x=accel_x-65536
	if accel_y>32768:
		accel_y=accel_y-65536
	if accel_z>32768:
		accel_z=accel_z-65536
	ax=int(accel_x*aRes+offset)
	if ax<0: ax=0
	if ax>255: ax=255
	ay=int(accel_y*aRes+offset)
	if ay<0: ay=0
	if ay>255: ay=255
	az=int(accel_z*aRes+offset)
	if az<0: az=0
	if az>255: az=255
	accel_array = [ax,ay,az]
	gyro = i2c.readfrom_mem(MPU6886_ADDRESS, MPU6886_GYRO_XOUT_H, 6)
	gyro_x = (gyro[0]<<8|gyro[1])
	gyro_y = (gyro[2]<<8|gyro[3])
	gyro_z = (gyro[4]<<8|gyro[5])
	if gyro_x>32768:
		gyro_x=gyro_x-65536
	if gyro_y>32768:
		gyro_y=gyro_y-65536
	if gyro_z>32768:
		gyro_z=gyro_z-65536
	gx=int(gyro_x*gRes+offset)
	if gx<0: gx=0
	if gx>255: gx=255
	gy=int(gyro_y*gRes+offset)
	if gy<0: gy=0
	if gy>255: gy=255
	gz=int(gyro_x*gRes+offset)
	if gz<0: gz=0
	if gz>255: gz=255
	gyro_array = [gx,gy,gz]
	return accel_array, gyro_array


lcd.rotation(2)
task = kpu.load("/sd/7118109ae3ea570e_mbnet10_quant.kmodel")#change model
labels=["seadog","Borbya","mermaid","Villo"] #change names.
sensor.reset()
sensor.set_pixformat(sensor.RGB565)
sensor.set_framesize(sensor.QVGA)
sensor.set_windowing((224, 224))
sensor.run(1)
lcd.clear()
while(True):
	accel_array,gyro_array = read_imu()
	img = sensor.snapshot()
	fmap = kpu.forward(task,img)
	plist=fmap[:]
	pmax=max(plist)
	#lcd.draw_string(40, 20, str(accel_array))
	#lcd.draw_string(10, 40, str(gyro_array))
	max_index=plist.index(pmax)
	if pmax > 0.95:
		#lcd.draw_string(40, 60, "Accu:%.2f Type:%s"%(pmax, labels[max_index].strip()))  #20-59,130-136,55-30 [side view] 100-130,130-136,9-20 [top view] 
        #the values are from 0 to 255 
		if accel_array[0] > 20 and accel_array[0] < 59 and accel_array[1] > 130 and accel_array[1] < 136 and accel_array[2] > 30 and accel_array[2] < 55:
			img.draw_image(image.Image("/sd/view2.jpg"), 50, 50,x_scale=0.5,y_scale=0.5,mask=image.Image("/sd/view2t.jpg"))
		if accel_array[0] > 60  and accel_array[0] < 130 and accel_array[1] > 130  and accel_array[1] < 137 and accel_array[2] > 8 and accel_array[2] < 20:
			img.draw_image(image.Image("/sd/view1.jpg"), 50, 50,x_scale=0.5,y_scale=0.5,mask=image.Image("/sd/view1t.jpg"))
	a = lcd.display(img)
a = kpu.deinit(task)
sys.exit()

[Bryam]

@staberas Como lo instalas no me reconoce si creo un ide en arduino

[staberas]

@bryam
The code above is for the maixpy (micropython) not arduino

[Alisson Brito]

@staberas I'm trying to run your example on the M5Stick V but I have a error message when trying to write_i2c for the first time. The error is: "OSError: [Errno 5] EIO". Do you know what does it means?

[m5stack]

you could find the MPU6886 example in this page:

https://docs.m5stack.com/#/en/related_documents/M5StickV-Maixpy

[purpledread]

@staberas

This code was very helpful. Thanks!

I tried adding temperature as well:

tmp = i2c.readfrom_mem(MPU6886_ADDRESS, MPU6886_TEMP_OUT_H, 2)
temp = (tmp[0]<<8|tmp[1])
temp = (float(temp) / 326.8) + 25.0;

I'm getting temps of 40.5C (105F). Am I doing something wrong or is this temperature the CPU temp?

Thanks,
/Chris