Unit V2 Connection
-
Hi, I have just received M5Stack Unit V2 AI camera and, when I connect to laptop, the fan runs but no connection available.
Please advise
ThanksIan
-
did you install the driver?
check this page and download the driver
-
Same problem for me as well. I submitted my post regarding the same issue yesterday. Waiting to hear from M5 on debugging / fixing it
-
-
I have the same problem with the AP.
PS: There are now 3 threads and no answer :(
-
unitv2% ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
link/ether 00:30:1b:ba:02:db brd ff:ff:ff:ff:ff:ff
inet 10.254.239.1/24 brd 10.254.239.255 scope global eth0
valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq qlen 1000
link/ether 00:e0:4c:05:22:59 brd ff:ff:ff:ff:ff:ff
4: wlan1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq qlen 1000
link/ether 02:e0:4c:05:22:59 brd ff:ff:ff:ff:ff:ff
inet 10.254.239.1/24 brd 10.254.239.255 scope global wlan1
valid_lft forever preferred_lft forever -
hello same problem.. no wifi AP, updated firmware no change...
USB drivers seems not working on my OSX 10.14.6
so its quite useless for now :(Update: I figured out how to get LAN up and running
removed SR9900Composite.kext SR9900.kext from /Library/Extensions/ and now Lan works (so its working without driver... and with driver its not working) -
This post is deleted! -
Hi, the new firmware still doesn't show any APs for me, even if I only connect it to USB-C from the charger. Does it switch to AP mode somewhere?
-
Same on my machine :( no AP at all....
-
sorry, the firmware seems still to have some bug. we are positioning the issues now.
-
@m5stack Any update on this? I've been waiting to get my hands on the device due to its wifi capabilities yet unable to get SSID?
-
Hello, @m5stack any update on the firmware?
-
What is happening with this its so disapointing months on from preorder i still cant even connect to the unit.
-
I couldn't even connect over USB and I emailed them about it, they suggested to restart the network interface. At first this didn't seem to work, but I think I just didn't wait long enough. So what now works for me is just bringing the network interface down, bringing it up again and waiting a couple of seconds:
$ sudo ip link set enx00e0993168d7 down $ sudo ip link set enx00e0993168d7 up $ ip a show dev enx00e0993168d7 13: enx00e0993168d7: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000 link/ether 00:e0:99:31:68:d7 brd ff:ff:ff:ff:ff:ff inet 10.254.239.243/24 brd 10.254.239.255 scope global dynamic noprefixroute enx00e0993168d7 valid_lft 42632sec preferred_lft 42632sec inet6 fe80::9c4a:2259:c022:588/64 scope link noprefixroute valid_lft forever preferred_lft forever
After this, I can access the web interface and ssh on 10.254.239.1 over USB. Wi-Fi doesn't seem to work and I didn't look at it because the USB network is fine for me for now.
-
@m5stack Why is this link dead?